D-Link DPS-500A/E Redundant power supply unit


    36,275.00 Kshs 36,275.00 Kshs 36275.0 KES


    Option not available

    This combination does not exist.

    Add to Cart Buy Now

    Terms and Conditions

    D-Link DPS-500A/E Redundant power supply unit

    Part Number: DPS-500A/E

    DPS-200A, DPS-500A and DPS-500DC - it's redundant power supplies (RPS), designed for use with switches D-Link. RPS is implemented in a robust metal housing with a connector for connecting them to the AC or DC power supply (depending on the model) and a connector for connecting to the internal power supply switch. Redundant Power Supply (RPS) is a low-cost device that allows to provide uninterrupted power in the event of an unexpected failure of the internal power supply switch, which may result in a shutdown of the switch devices connected to its ports, or the entire network. Providing necessary for the output power switch, the RPS can improve the reliability of the device.

    Redundant power supply

    Each RPS D-Link continually monitors the status of the internal power supply. In case of power failure immediately run a backup power source, so that the LAN switch and the connected devices can continue to work. This increases the fault tolerance of the network infrastructure and executed by protection network disconnects the power supply due to the failure of one of the network devices.

     Easy and flexible installation

    Installing the DPS Series device does not require any changes in the settings of the LAN switch. Except DPS-500DC, each RPS is equipped with an internal power supply and can be connected to any AC power source 90 to 264 volts AC with a frequency of 47 to 63 Hz with a standard power cable. DPS-500DC is connected to a DC power supply instead of the AC.

    Modular redundant power supplies

    DPS-200A, 500A, and DPS-DPS-500DC - are modular redundant power supplies that can be used as a stand-alone device, or set the DPS-800 chassis. The chassis can be mounted in a standard 19-inch rack. The chassis can be installed more the RPS, which can be connected to the switches mounted in the same rack.

    The chassis is mounted in a rack

    DPS-800 chassis allows up to two DPS-200A modules, DPS-500A or DPS-500DC in an equipment rack. Using the chassis saves space and at the same time, the cable system will look neat. All the RPS, installed in the chassis, connected directly to the power supply and can be replaced in "hot" mode


    Redundant Power Protection

    Connect to a variety of D-Link Gigabit switches

    Provide backup power for switch’s built-in power supply

    Over-current protection

    LED status indicators

    Flexible Deployment Options

    Can be installed as stand-alone power supply units or mounted in a 19-inch multi-slot chassis

    Hot swappable when installed in a chassis

    Solid metal case housing

    Compatible Products



















    1 Requires a DPS-CB150-2PS to connect with the DGS-3000 Series. DPS-CB150-2PS available by special request.

    Technical Specifications



    • 172 x 257 x 43 mm (6.8 x 10.1 x 1.7 inches)

    • Panel size: 196 x 52 mm (7.7 x 2.04 inches)


    • 1.51 kg

    Input Voltage Range

    • 90 to 264 V AC

    Input Frequency

    • 47 to 63 Hz

    Max Input Current

    • 1A at 240 V AC

    Max Inrush Current

    • 60 A at 230 V AC


    • 75 %

    Operating Temperature

    • 0 to 50 °C (32 to 122 °F)

    Storage Temperature

    • -45 to 85 °C (-49 to 185 °F)

      Operating Humidity

    • 10 to 90% RH

    Storage Humidity

    • 10 to 95% RH


    • 400,000 hours

    Product Datasheet

    This is a preview of the recently viewed products by the user.
    Once the user has seen at least one product this snippet will be visible.

    Recently viewed Products